31++ How Do I Install A Water Line For A Refrigerator Ideas
How do i install a water line for a refrigerator. If theres no water supply pipe available install a tea adapter to an existing hookup point. Water can be provided in one of two ways. Connect the refrigerator water line to the third outlet of the tee fitting. Turn off the water supply and drain the cold water valve by turning on the cold water faucet. Slide on the pressure nut and then the ferrule from the water line kit onto the plastic water line then carefully attach the nut water line to the refrigerator water inlet valve. The icemaker kit will come with a water line a coupler a new valve and a few brass parts such as nuts and ferrules. If your refrigerator is across the room from your kitchen sink there may be a closer water supply line in an adjacent bathroom or garage. Preferably it will be in fairly close proximity to where the refrigerator will be positioned but you have about 25 feet of leeway given the length of the tubing supplied in the kit. At one time this was typically done with 14-inch bendable copper tubing that was snaked from the refrigerator to the nearest source of water and tapped into the water line using a saddle valve or other fitting. By connecting the fridge directly to plumbing via a water line or by manually adding water to a reservoir inside the fridge. Remove the parts from the packaging. Do not over tighten.
If theres a water supply pipe available all you need to do is run your flex tube from the pipe to the refrigerator. Water line must be connected to potable water only If the Refrigerator is installed in area with low water pressure below 20psi a booster pump should be installed to compensate for the low pressure A universal water supply kit is available at extra cost from the dealer. Thread the water line included in the ice maker installation kit from the area behind the refrigerator to beneath the sink. Slowly open up the shutoff valve if you used the under counter method to connect it or in my case the main water valve and verify to make sure there arent any leaks on the main water line. How do i install a water line for a refrigerator Insert a tee into the cold water line. Its currently positioned to stick into the side of a new pantry unit and would interfere with the slide out drawers so I figured I could cut into the wall and run a new copper. With the refrigerator out of its hole go ahead and proceed to testing. Turn the water on at the water valve you just installed. Installing your water line is an easy process that can be completed in some minutes. Turn on the cold water at the kitchen faucet to relief pressure in the water line. Install one end of the line on the refrigerator by threading the line through the nut adding one of the brass ferrules to the line and screwing the nut in place on the refrigerator valve. Installing a Refrigerator Water Line Is Easy Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. Then open up the valve for the fridge connection and do the same thing.
How To Install A Refrigerator With Ice And Water Dispensers
How do i install a water line for a refrigerator Connect the sink water supply line to the tee fitting.
How do i install a water line for a refrigerator. I inserted the water line into the opening of the valves brass compression fitting and tightened it with a crescent wrench. The first step to establishing a water supply line to the fridge is to locate a water pipe to tap into. If your sink does not have a shut-off valve.
If it has a lever-type handle turn the lever so it is perpendicular to the water pipe. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. Close the shutoff valve by turning it clockwise until it stops.
With the saddle valve installed on the water pipe it was time to attach the 14-inch copper line for the refrigerator that I had previously pulled down through the basement ceiling from the kitchen. Step 10 Now it is time to check for water leaks. TAPPING A SINK WITHOUT A VALVE.
Refrigerators that feature built-in water dispensers or automatic ice makers need to be connected to a water source. Rather than run a water line up though the hot attic or around the room to feed the water dispenser and icemaker Im hoping I can take advantage of this close source. If it were me I would drill a hole in the wall between the studs and fish it up to the ceiling and run it over to where it can be dropped where the fridge goes but then my home has PEX plumbing so that of course would be possible.
Leave the excess water line behind the refrigerator.
How do i install a water line for a refrigerator Leave the excess water line behind the refrigerator.
How do i install a water line for a refrigerator. If it were me I would drill a hole in the wall between the studs and fish it up to the ceiling and run it over to where it can be dropped where the fridge goes but then my home has PEX plumbing so that of course would be possible. Rather than run a water line up though the hot attic or around the room to feed the water dispenser and icemaker Im hoping I can take advantage of this close source. Refrigerators that feature built-in water dispensers or automatic ice makers need to be connected to a water source. TAPPING A SINK WITHOUT A VALVE. Step 10 Now it is time to check for water leaks. With the saddle valve installed on the water pipe it was time to attach the 14-inch copper line for the refrigerator that I had previously pulled down through the basement ceiling from the kitchen. Close the shutoff valve by turning it clockwise until it stops. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. If it has a lever-type handle turn the lever so it is perpendicular to the water pipe. If your sink does not have a shut-off valve. The first step to establishing a water supply line to the fridge is to locate a water pipe to tap into.
I inserted the water line into the opening of the valves brass compression fitting and tightened it with a crescent wrench. How do i install a water line for a refrigerator
Indeed recently has been sought by consumers around us, perhaps one of you. Individuals are now accustomed to using the internet in gadgets to see image and video information for inspiration, and according to the name of this post I will talk about about How Do I Install A Water Line For A Refrigerator.
How do i install a water line for a refrigerator. Leave the excess water line behind the refrigerator. Leave the excess water line behind the refrigerator.
If you are searching for How Do I Install A Water Line For A Refrigerator you've come to the perfect location. We ve got 51 graphics about how do i install a water line for a refrigerator including pictures, photos, photographs, wallpapers, and much more. In these page, we also provide number of images available. Such as png, jpg, animated gifs, pic art, symbol, blackandwhite, transparent, etc.
How To Install Water Line For Samsung Refrigerator Samsung Singapore
How To Install A Water Line To Your Fridge Youtube